Ford BA-FG Bolt In Spring Locators (Convert From Bags)
These bolt in Spring locators, allow you to install springs back into your vehicle after installing bolt in airbag suspension. Kit includes: 2x Lower plates 2x Lower bolts 2x Weld in nuts **...
00Control your air suspension valves with this plug and play window switch module
The AS-WSM-HOL-001 is a 9 output “plug n’ play” solution to allow for independent control of 8 airbags using the factory VT VX master window switch. The control is switched between air suspension and windows using the factory child lock button. When the child lock button is off the window switches work as normal. Once the child lock button is pressed the output for compressor is turned on and the 8 valve outputs can be turned on using the window switches.
The front left hand window switch used to lift and lower the window will now inflate and deflate the front left airbag and so on for all other window switches.
Remove the gear surround trim by taking out the 2x Phillips head screws under the head unit pocket. Lift the gear surround from the back (near the master window switch control) and then disconnect the master window switch module. Pull the gear surround out and set aside. Remove the driver’s side front right centre console trim allowing access to tuck the AS-WSM-HOL-001 up into the cavity on the right-hand side of the head unit. Run the plug wiring under the centre console and tuck it up under the air vents that run to the rear of the centre console. Wire in the airbag outputs including compressor killswitch as required (see below wiring info) If not using all outputs or compressor killswitch then make sure you tape the unused wiring up individually so bare wires can touch another. Plug the harness into the vehicle wiring and then refit the centre console gear surround. Plug the master window switch into the new harness and fit the gear surround back into the clips. Refit the side trim and you are all set to go.
Toggle between window switch mode and air suspension control mode using the child lock button. When in window switch mode only use 1x window switch at a time to reduce the amount of current flowing through the module. You should always only modify 1 window at a time and never continue to hold a button once the window has reached full position (up or down)
1: Front Left Airbag 2: Front Right Airbag
3: Rear Left Airbag 4: Rear Right Airbag
1 Up: Brown 2 Up: Green 3 Up: Yellow 4 Up: Blue
1 Down: Purple 2 Down: Pink 3 Down: Grey 4: Down: White
Compressor 12v + feed: Orange
1x Window swotch plug-n'-play module
1x Instruction manual (same as above information)
THIS KIT DOES NOT INCLUDE A MASTER WINDOW SWITCH. USE YOUR EXISTING WINDOW SWITCH WITH THIS MODULE
16 other products in the same category:
These bolt in Spring locators, allow you to install springs back into your vehicle after installing bolt in airbag suspension. Kit includes: 2x Lower plates 2x Lower bolts 2x Weld in nuts **...
Height Sensor Suits Accuair New Plug The AArot120 Height sensors are direct replacements for the Accuair Elevel height sensors as well as other autolevel sensors that use the AA-ROT-120...
Aluminium air tank 5 port 3 Gallon (approx 9 litres) Tank Size is L450mm x H220mm x W180mm 2x 3/8" NPT Ports on ends 3x 1/4" NPT Ports on 1 end ( See pictures )
BRASS Male Elbow 90 Degree NPT Thread Brass Finish Male - Male Thread 90 Degree Angle
Specifications: The VBVU2BK is a 2-way 4 solenoid valve block that allows for independent control of 2 airbags. It features dual 1/4” NPT inlet and exhaust ports allowing for multiple install...
Beautiful blue OR Red display with optional Blue or Red night time display ( Changes due to how you wire see manual supplied for details) Get rid of your air lines to your gauges and make the...
These bolt in Spring locators, allow you to install springs back into your vehicle after installing bolt in airbag suspension. Kit includes: 2x Upper Plates 2x Lower plates 4x Upper bolts and...
Get down low as desired with this rear air suspension kit for VT-VZ vehicles. This Kit comes with 95% of what you need ( missing a few installation accessories such as grommets, split tube,...
BRASS Bushing NPT Thread Brass Finish Male - Female Thread
Finish: Black and Chrome style finish with Green and Orange Needles Dimensions: 52mm Mounting Diam Thread Size: 1/8" NPT Thread Working Range: Approximately 0-200PSI Package Includes: 1x 200 PSI...
3 PROGRAMMABLE HEIGHT Lowered / Ride Height / Raised plus All Down when using e+ Height* AUTOMATIC CALIBRATION Learns how to adjust for your vehicle when using e+ Height* BLUETOOTH Long...
Brass Straight Hex Nipple Male NPT Thread -Male NPT Thread Brass Finish
Get down low as desired with this air suspension kit for VT-VZ vehicles. This Kit comes with 95% of what you need ( missing a few installation accessories such as grommets, split tube, solder,...
6" Double convoluted airbag Perfect for Ford BA-FG (with upper plates) and other direct bolt in airbag suspension setups. Weight: 1.9kg Diameter: 153 mm Max Load: 2500lb Load Rating @ 100psi : 635...
Get down low as desired with this rear air suspension kit for BA-FG vehicles. This Kit comes with 95% of what you need ( missing a few installation accessories such as grommets, split tube,...
DURABLE Manufactured from durable materials to help ensure longevity. CERTIFIED PART This product is a 100% certified AccuAir replacement part. GUARANTEED FITMENT AccuAir guarantees...