Get down low as desired with this rear air suspension kit for VT-VZ vehicles.
This Kit comes with 95% of what you need ( missing a few installation accessories such as grommets, split tube, solder, tape etc) to get your vehicle rear bagged!
Inlcuded in the kit:
- 3 Gal tank ( as standard)
- 480c Black series compressor
- Compressor wiring kit (7m of 5mm wire + 150psi pressure switch + auto reset breaker + relay)
- Switch panel wiring with compressor killswitch included
- Dual digital gauge and switch panel with compressor killswitch
- All Brass DOT approved fittings
- DX2600 double convoluted air springs
- 2 way valve block
- 4m of 3/8" Airline for bags
- Slimline digital pressure sender units and wiring
- Water trap and filter
- 1/4" Remote drain kit( Schrader valve style)
- Airbag mounting hardware
- Airbag hole pattern templates
- brief installation diagrams ( NOT FULL INSTRUCTIONS).
This kit assumes you have knowledge on how to install a rear airbag suspension setup to these vehicles it does not include a full detailed how to manual.
16 other products in the same category:
Get down low as desired with this rear air suspension kit for BA-FG vehicles.
This Kit comes with 95% of what you need ( missing a few installation accessories such as grommets, split tube,...
7" Double convoluted airbag
Perfect for Holden VT-VZ other direct bolt in airbag suspension setups.
Weight: 2.5kg
Diameter: 180mm
Max Load: 2600lb
Load Rating @ 100psi : 970.7kg
Stud Size: 3/8"...
BRASS Street Elbows
NPT Thread
Brass Finish
Male - Female Thread
6" Double convoluted airbag
Perfect for Ford BA-FG (with upper plates) and other direct bolt in airbag suspension setups.
Weight: 1.9kg
Diameter: 153 mm
Max Load: 2500lb
Load Rating @ 100psi : 635...
Height Sensor
Suits Accuair New Plug
The AArot120 Height sensors are direct replacements for the Accuair Elevel height sensors as well as other autolevel sensors that use the AA-ROT-120...
Bolt in air suspension front strut assemblies
These bags allow for full safe travel compared to some others on the market. Using triple convoluted bags means the full travel can be achieved without...
Whats included?
1x electric momentary switch
Perfect for use in air suspension with electronic valve setups to activate both inflate and deflate solenoids.
10A Rating 125v
Colored LED indicates the status of your compressor.
Accuair’s patented TouchPad+ is the latest technology in air suspension management. This touchpad allows you to easily control your air...
These bolt in Spring locators, allow you to install springs back into your vehicle after installing bolt in airbag suspension. Kit includes:
2x Lower plates
2x Lower bolts
2x Weld in nuts
**...
Beautiful blue OR Red display with optional Blue or Red night time display ( Changes due to how you wire see manual supplied for details)
Get rid of your air lines to your gauges and make the...
DOT Approved Brass Swivel Elbow
Male NPT Thread - Push to Connect Tube ( Outside Diameter)
DOT Approved
O Rig Seals
Brass Finish (1/8" NPT- 5/32" ( 4mm) are Nickle finish)
If you are looking for an entry level control system that is simple while offering smartphone capabilities, the e+ Connect wireless controller is a great choice. This wireless switch box allows...
6mm Clear Acrylic Sensor arm replacement Replace your broken sensor arm with this cnc cut replacement arm Keeps the standard hole spacing and uses your existing screws to mount to sensor
(Sensor...
BRASS Male Elbow 90 Degree
NPT Thread
Brass Finish
Male - Male Thread 90 Degree Angle
Aluminium tank 1 Gallon, 3 port silver (approx 3 litres) H130mm x W95mm x L400mm with drain
2x 3/8" NPT Ports
1x 1/4" NPT Drain port
Specifications:
The ASWK-GP3-VU2-5 is a plug and play harness to go from the GP3 series gauge panel to the VBVU2 series valve block. Simply plug in the connector to the valve block and connect the...
