Ford BA-FG Bolt In Spring Locators (Convert From Bags)
These bolt in Spring locators, allow you to install springs back into your vehicle after installing bolt in airbag suspension. Kit includes: 2x Lower plates 2x Lower bolts 2x Weld in nuts **...
00Control your air suspension valves with this plug and play window switch module
The AS-WSM-HOL-001 is a 9 output “plug n’ play” solution to allow for independent control of 8 airbags using the factory VT VX master window switch. The control is switched between air suspension and windows using the factory child lock button. When the child lock button is off the window switches work as normal. Once the child lock button is pressed the output for compressor is turned on and the 8 valve outputs can be turned on using the window switches.
The front left hand window switch used to lift and lower the window will now inflate and deflate the front left airbag and so on for all other window switches.
Remove the gear surround trim by taking out the 2x Phillips head screws under the head unit pocket. Lift the gear surround from the back (near the master window switch control) and then disconnect the master window switch module. Pull the gear surround out and set aside. Remove the driver’s side front right centre console trim allowing access to tuck the AS-WSM-HOL-001 up into the cavity on the right-hand side of the head unit. Run the plug wiring under the centre console and tuck it up under the air vents that run to the rear of the centre console. Wire in the airbag outputs including compressor killswitch as required (see below wiring info) If not using all outputs or compressor killswitch then make sure you tape the unused wiring up individually so bare wires can touch another. Plug the harness into the vehicle wiring and then refit the centre console gear surround. Plug the master window switch into the new harness and fit the gear surround back into the clips. Refit the side trim and you are all set to go.
Toggle between window switch mode and air suspension control mode using the child lock button. When in window switch mode only use 1x window switch at a time to reduce the amount of current flowing through the module. You should always only modify 1 window at a time and never continue to hold a button once the window has reached full position (up or down)
1: Front Left Airbag 2: Front Right Airbag
3: Rear Left Airbag 4: Rear Right Airbag
1 Up: Brown 2 Up: Green 3 Up: Yellow 4 Up: Blue
1 Down: Purple 2 Down: Pink 3 Down: Grey 4: Down: White
Compressor 12v + feed: Orange
1x Window swotch plug-n'-play module
1x Instruction manual (same as above information)
THIS KIT DOES NOT INCLUDE A MASTER WINDOW SWITCH. USE YOUR EXISTING WINDOW SWITCH WITH THIS MODULE
16 other products in the same category:
These bolt in Spring locators, allow you to install springs back into your vehicle after installing bolt in airbag suspension. Kit includes: 2x Lower plates 2x Lower bolts 2x Weld in nuts **...
BRASS Bushing NPT Thread Brass Finish Male - Female Thread
Specifications: The VBVU2BK is a 2-way 4 solenoid valve block that allows for independent control of 2 airbags. It features dual 1/4” NPT inlet and exhaust ports allowing for multiple install...
Finish: Black and Chrome style finish with Green and Orange Needles Dimensions: 52mm Mounting Diam Thread Size: 1/8" NPT Thread Working Range: Approximately 0-200PSI Package Includes: 1x 200 PSI...
Brass Socket Plug Male NPT Thread Brass Finish Allan Key Drive
Get down low as desired with this air suspension kit for VT-VZ vehicles. This Kit comes with 95% of what you need ( missing a few installation accessories such as grommets, split tube, solder,...
Aluminium tank 1 Gallon, 3 port silver (approx 3 litres) H130mm x W95mm x L400mm with drain 2x 3/8" NPT Ports 1x 1/4" NPT Drain port
If you are looking for an entry level control system that is simple while offering smartphone capabilities, the e+ Connect wireless controller is a great choice. This wireless switch box allows...
Auto Drain 1/4" NPT Air Filter / Water Trap Female NPT Thread - 1/4" 220psi rated 145psi normal working pressure ( Ideal for 150psi pressure switches) Auto Drain ( When tank pressure gets low or...
BRASS Hex Coupling NPT Thread Brass Finish Female - Female Thread
Height Sensor Suits Accuair New Plug The AArot120 Height sensors are direct replacements for the Accuair Elevel height sensors as well as other autolevel sensors that use the AA-ROT-120...
DOT Approved Brass Swivel Elbow Male NPT Thread - Push to Connect Tube ( Outside Diameter) DOT Approved O Rig Seals Brass Finish (1/8" NPT- 5/32" ( 4mm) are Nickle finish)
Interrupt Rating: 2.5KA@12VDCOperating temp: -40°C to 85°C (-40°F to 185°F)Storage temp: -40°C to 125°C (-40°F to 260°F)Terminal: #10-32 thread with quick connector.Mounting Torque Rating: 15in-lb...
2 Corner Gauge panel with switches This gauge panel comes complete with left and right 2 way momentary switches ( up and down) as well as a digital 2 way gauge! This kit is perfect for controlling...
DURABLE Manufactured from durable materials to help ensure longevity. CERTIFIED PART This product is a 100% certified AccuAir replacement part. GUARANTEED FITMENT AccuAir guarantees...
4 Corner Height Sensor Harness Direct replacement for Accuair, Levelride and other autolevel system sensor harnesses. Labelled Sensor plugs 1- Front Left 2- Front Right 3- Rear Left 4- Rear Right...