Hex Nipple NPT - NPT Straight Male Brass Fittings...
Brass Straight Hex Nipple Male NPT Thread -Male NPT Thread Brass Finish
Control your air suspension valves with this plug and play window switch module
The AS-WSM-HOL-002 is a 9 output “plug n’ play” solution to allow for independent control of 8 airbags using the factory VY VZ master window switch. The control is switched between air suspension and windows using the factory child lock button. When the child lock button is off the window switches work as normal. Once the child lock button is pressed the output for compressor is turned on and the 8 valve outputs can be turned on using the window switches.
The front left hand window switch used to lift and lower the window will now inflate and deflate the front left airbag and so on for all other window switches.
Remove the gear surround trim by taking out the 1x Phillips head screw under the head unit pocket. Lift the gear surround from the back (near the master window switch control) and then disconnect the master window switch module. Pull the gear surround out and set aside. Remove the driver’s side front right centre console trim allowing access to tuck the AS-WSM-HOL-002 up into the cavity under the head unit and air vent. Run the plug wiring under the centre console and tuck it up under the air vents that run to the rear of the centre console. Wire in the airbag outputs including compressor killswitch as required (see below wiring info) If not using all outputs or compressor killswitch then make sure you tape the unused wiring up individually so bare wires can touch another. Plug the harness into the vehicle wiring and then refit the centre console gear surround. Plug the master window switch into the new harness and fit the gear surround back into the clips. Refit the side trim and you are all set to go.
Toggle between window switch mode and air suspension control mode using the child lock button. When in window switch mode only use 1x window switch at a time to reduce the amount of current flowing through the module. You should always only modify 1 window at a time and never continue to hold a button once the window has reached full position (up or down)
1: Front Left Airbag 2: Front Right Airbag
3: Rear Left Airbag 4: Rear Right Airbag
1 Up: Brown 2 Up: Green 3 Up: Yellow 4 Up: Blue
1 Down: Purple 2 Down: Pink 3 Down: Grey 4: Down: White
Compressor 12v + feed: Orange
1x Window swotch plug-n'-play module
1x Instruction manual (same as above information)
THIS KIT DOES NOT INCLUDE A MASTER WINDOW SWITCH. USE YOUR EXISTING WINDOW SWITCH WITH THIS MODULE
16 other products in the same category:
Brass Straight Hex Nipple Male NPT Thread -Male NPT Thread Brass Finish
6″ diameter bag Single 1/2″ NPT port Rated @ 250psi 6061-T6 CNC machined aluminum NPT port Zinc plated steel threaded inserts 2.7″ min. collapsed height 11″ max. height Internal bumpstops...
BRASS Male Elbow 90 Degree NPT Thread Brass Finish Male - Male Thread 90 Degree Angle
Finish: Black and Chrome style finish with Green and Orange Needles Dimensions: 52mm Mounting Diam Thread Size: 1/8" NPT Thread Working Range: Approximately 0-200PSI Package Includes: 1x 200 PSI...
Get down low as desired with this air suspension kit for VT-VZ vehicles. This Kit comes with 95% of what you need ( missing a few installation accessories such as grommets, split tube, solder,...
12v Air Compressor - Ideal for Air Suspension Specifications: Model: ASAC480B18Voltage: 12vMax Current: 23AMax Working...
If you are looking for an entry level control system that is simple while offering smartphone capabilities, the e+ Connect wireless controller is a great choice. This wireless switch box allows...
Height Sensor Suits Accuair New Plug The AArot120 Height sensors are direct replacements for the Accuair Elevel height sensors as well as other autolevel sensors that use the AA-ROT-120...
Specifications: The ASWK-GP3-VU2-5 is a plug and play harness to go from the GP3 series gauge panel to the VBVU2 series valve block. Simply plug in the connector to the valve block and connect the...
BRASS Bushing NPT Thread Brass Finish Male - Female Thread
Finish: Black and Chrome style finish with RED LED display Dimensions: 52mm Mounting Diam Sender units: 1/8" NPT Thread Working Range: Approximately 0-220PSI
FeaturesSlam Specialties is proud to release the MC.1-SS. A microprocessor controlled, solid state switch-box and receiver for your air ride control.Compact and lightweight design coupled with...
4 Corner Height Sensor Harness Direct replacement for Accuair, Levelride and other autolevel system sensor harnesses. Labelled Sensor plugs 1- Front Left 2- Front Right 3- Rear Left 4- Rear Right...
Get down low as desired with this rear air suspension kit for VE-VF vehicles. This Kit comes with 95% of what you need ( missing a few installation accessories such as grommets, split tube,...
BRASS Hex Coupling NPT Thread Brass Finish Female - Female Thread
Colored LED indicates the status of your compressor. Accuair’s patented TouchPad+ is the latest technology in air suspension management. This touchpad allows you to easily control your air...